Hotendy
-
Přidat k OblíbenýmE3D RapidChange Revo™ Micro - 1.75mm, 24V Fully Loaded Kit
Smaller, lighter, and better than ever before, our Revo Micro HotEnd uses the smallest heatsink we’ve produced so far. Weighing in at only 30g, use Revo Micro to squeeze more speed performance from your motion system. Adaptable to Bowden or direct drive setups, Revo Micro is fully compatible with our Revo ecosystem, so you can easily change nozzles without tools or hot tightening at room...
Na objednávku (10001 ks)
4139 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Brass 1.75mm Variety Nozzle Pack
Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening – just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Compatible with Revo cold sides, including Revo Six, Revo Micro, and Revo Hemera No need to hot tighten – each Revo Nozzle is a factory-assembled...
Na objednávku (10001 ks)
1989 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ HeaterCore 12V
The Revo HeaterCore is a heating and sensing architecture for E3D’s RapidChange Revo ecosystem. It combines a powerful heater and temperature probe into a convenient, compact package.
Na objednávku (10001 ks)
979 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ CR HeaterCore 24V
This is a special Revo HeaterCore intended for use with the Revo CR. It uses a 40W heater and a 100K NTC thermistor, which has the same response as a stock Creality thermistor, saving you the hassle of any firmware changes to your Creality 3D printer.
Na objednávku (10001 ks)
979 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Fully Loaded Sock Pack
E3D colour-coded silicone socks for Revo Nozzles. Never run out of silicone socks for your Revo 3D printing setup! This colour-coded sock kit includes ten silicone socks for all your 3D printing needs.
Na objednávku (10001 ks)
239 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Spring Triple Pack
These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo Hemera. The spring keeps the HeaterCore firmly attached to the cold side, while pushing it into the nozzle for improved thermal conductivity.
Na objednávku (10001 ks)
79 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Brass 1.75mm 0.25mm Nozzle
Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening – just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Compatible with Revo cold sides, including Revo Six, Revo Micro, and Revo Hemera No need to hot tighten – each Revo Nozzle is a factory-assembled...
Na objednávku (10001 ks)
669 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ HeaterCore 24V
The Revo HeaterCore is a heating and sensing architecture for E3D’s RapidChange Revo ecosystem. It combines a powerful heater and temperature probe into a convenient, compact package.
Na objednávku (10000 ks)
979 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Hemera XS - 1.75mm, 12V Fully Loaded Nozzle Kit
Revo Hemera XS is a compact dual-drive extrusion system. It’s 92g lighter and 11mm shorter than classic Hemera, so it can move faster on your 3D printer’s motion system with less inertia, reducing print artefacts such as ghosting. A specially designed heatsink makes it compatible with Revo Nozzles, and with the addition of a Hemera HeatBreak (sold separately) it works with the E3D V6 ecosystem,...
Na objednávku (10001 ks)
7339 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Brass 1.75mm 0.15mm Nozzle
Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening – just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Compatible with Revo cold sides, including Revo Six, Revo Micro, and Revo Hemera No need to hot tighten – each Revo Nozzle is a factory-assembled...
Na objednávku (10001 ks)
669 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ ObXidian Nozzle 0,4 mm
Revo ObXidian is E3D's latest abrasive resistant Revo Nozzle offering, specifically designed for printing fibre-filled polymers. Unlike other abrasion resistant Nozzles, ObXidian’s copper alloy construction has a similar thermal performance to Brass, making it a true drop-in replacement. Just use the same slicer profiles as for your Brass Nozzles.Key Features:Material: Copper/Hardened...
Na objednávku (10001 ks)
1719 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ ObXidian Nozzle 0,6 mm
Revo ObXidian is E3D's latest abrasive resistant Revo Nozzle offering, specifically designed for printing fibre-filled polymers. Unlike other abrasion resistant Nozzles, ObXidian’s copper alloy construction has a similar thermal performance to Brass, making it a true drop-in replacement. Just use the same slicer profiles as for your Brass Nozzles.Key Features:Material: Copper/Hardened...
Na objednávku (10001 ks)
1719 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ CR - 1.75mm, 12V Fully Loaded Nozzle Kit
Revo CR is a drop-in upgrade for some of the most popular Creality 3D printers available, including the Creality CR-10 and Ender 3 series.
Na objednávku (10001 ks)
4139 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Hemera XS - 1.75mm, 12V Single Nozzle Kit
Revo Hemera XS is a compact dual-drive extrusion system. It’s 92g lighter and 11mm shorter than classic Hemera, so it can move faster on your 3D printer’s motion system with less inertia, reducing print artefacts such as ghosting. A specially designed heatsink makes it compatible with Revo Nozzles, and with the addition of a Hemera HeatBreak (sold separately) it works with the E3D V6 ecosystem,...
Na objednávku (10001 ks)
6049 Kč
-
Přidat k OblíbenýmE3D RapidChange Revo™ Micro - 1.75mm, 12V Fully Loaded Kit
Smaller, lighter, and better than ever before, our Revo Micro HotEnd uses the smallest heatsink we’ve produced so far. Weighing in at only 30g, use Revo Micro to squeeze more speed performance from your motion system. Adaptable to Bowden or direct drive setups, Revo Micro is fully compatible with our Revo ecosystem, so you can easily change nozzles without tools or hot tightening at room...
Na objednávku (10001 ks)
4139 Kč